Shim › Guides › Steps for a ceiling height
For a 9-foot ceiling over 2x10 floor joists, the total rise is 118-1/2 inches (9' 10-1/2"), not 108 inches. The total rise runs from the finished floor below to the finished floor above, so it includes the floor framing, the 3/4-inch subfloor and the 1/2-inch ceiling drywall. That takes 16 risers at 7-7/16 inches each, 15 treads, and a total run of 12' 6" at 10-inch treads. The numbers assume 2x10 joists, 3/4-inch subfloor, 1/2-inch drywall and no finish flooring on top.
Total rise = ceiling height + joist depth + 3/4" subfloor + 1/2" drywall. Risers are the fewest that keep each riser at or under 7-3/4 inches (IRC R311.7.5.1). Riser heights are shown to the nearest 1/16 inch.
| Ceiling height | Floor framing (joist depth) | Total rise | Risers | Riser height |
|---|---|---|---|---|
| 8 ft | 2x8 (7-1/4") | 8' 8-1/2" | 14 | 7-7/16" |
| 8 ft | 2x10 (9-1/4") | 8' 10-1/2" | 14 | 7-5/8" |
| 8 ft | 2x12 (11-1/4") | 9' 0-1/2" | 14 | 7-3/4" |
| 8 ft | 11-7/8" I-joist | 9' 1-1/8" | 15 | 7-1/4" |
| 9 ft | 2x8 (7-1/4") | 9' 8-1/2" | 16 | 7-5/16" |
| 9 ft | 2x10 (9-1/4") | 9' 10-1/2" | 16 | 7-7/16" |
| 9 ft | 2x12 (11-1/4") | 10' 0-1/2" | 16 | 7-9/16" |
| 9 ft | 11-7/8" I-joist | 10' 1-1/8" | 16 | 7-9/16" |
| 10 ft | 2x8 (7-1/4") | 10' 8-1/2" | 17 | 7-9/16" |
| 10 ft | 2x10 (9-1/4") | 10' 10-1/2" | 17 | 7-11/16" |
| 10 ft | 2x12 (11-1/4") | 11' 0-1/2" | 18 | 7-3/8" |
| 10 ft | 11-7/8" I-joist | 11' 1-1/8" | 18 | 7-3/8" |
| 12 ft | 2x8 (7-1/4") | 12' 8-1/2" | 20 | 7-5/8" |
| 12 ft | 2x10 (9-1/4") | 12' 10-1/2" | 20 | 7-3/4" |
| 12 ft | 2x12 (11-1/4") | 13' 0-1/2" | 21 | 7-7/16" |
| 12 ft | 11-7/8" I-joist | 13' 1-1/8" | 21 | 7-1/2" |
Treads = risers − 1. Total run = treads × tread depth. Stringer length is the diagonal from the bottom of the rise to the end of the run, √(total rise² + total run²). Tread depth is at least 10 inches (IRC R311.7.5.2), so the table shows 10-inch and 11-inch treads.
| Ceiling height | Risers | Treads | Total run, 10" treads | Total run, 11" treads | Stringer length, 10" treads |
|---|---|---|---|---|---|
| 8 ft | 14 | 13 | 10' 10" | 11' 11" | 14' 0-1/16" |
| 9 ft | 16 | 15 | 12' 6" | 13' 9" | 15' 11-3/16" |
| 10 ft | 17 | 16 | 13' 4" | 14' 8" | 17' 2-1/2" |
| 12 ft | 20 | 19 | 15' 10" | 17' 5" | 20' 4-7/8" |
The riser height is rounded to 1/16 inch. Sixteen risers at 7-7/16 inches add up to 119 inches, half an inch more than the 118-1/2-inch rise, so don't step off all 16 at the rounded number. The exact height is 7-13/32 inches (118-1/2 ÷ 16), which Shim shows at its 1/32-inch setting. On a 1/16-inch tape, alternate 7-3/8 and 7-7/16 inches, eight of each, which also adds up to 118-1/2 inches. The IRC allows up to 3/8 inch between the tallest and the shortest riser in a flight (R311.7.5.1), so a 1/16-inch alternation is fine, but leaving the whole half inch on one riser is not.
Do it on the job with Shim. Shim: Construction Calculator for iPhone is on the App Store. Its stairs tool, in Pro, gives the risers, riser height, treads, total run and stringer length, and checks them against the IRC limits. See Shim's page.
Published by Avira LLC · Updated 2026-11-13 · Written with AI assistance. Every number is computed with the same formulas as Shim and checked against worked examples.